ducati pick up sensor

Mr Jurassic · February 15th, 2011, 09:45 AM

Ok guys i recently had this error and people have been looking for this pick up sensor well after 5 hours of research i finally found it.

In picture #1 you can see this is the left side of the bike.
This is the Timing pick-up sensor here

In picture #2 this is is the hole where it goes. double check the quality of these o rings

In picture #3 After cleaning the sensor re-grease only the tip of the sensor

In picture #4 Fitment of the sensor back into the crackcase

In picture #5 position the 0.6mm shim

*NOTE: if replaceing the sensor you will have to take the side of the crankcase off and measure the air gap between the sensor and the teeth on the timing gear.
The distence between the timing gear and the sensor should be between .8 and .6 mm

*NOTE: I am not responsible for voiding/ or blowing up of any engines.

lucky phil · February 15th, 2011, 10:08 AM

It took you 5hrs to find the pickup sensor?OK
You dont need to lube the end of the sensor,first oring will simply wipe it off and there will be nothing on it when it hits the second ring.Better to smear grease down the hole to help it ease through the o rings.
You dont need to remove the side cover to set the gap.There are a couple of ways to do it without resorting to that depending on the equipment you have available.
Ciao

Mr Jurassic · February 15th, 2011, 10:17 AM

I agree.... Just those are pic's and instructions from the workshop manual... sorry but you do a google search for pick up sensor 34.0 error and see if you can find the sensor... this is just here to save someone the time it took me.

All of that info is from the Workshop manual.
And you will have to remove the side cover if you are REPLACING the sensor with a new one.
To measure the correct air gap from timeing gear to tip of NEW sensor

lucky phil · February 16th, 2011, 12:46 AM

Quote:

Originally Posted by Mr Jurassic

I agree.... Just those are pic's and instructions from the workshop manual... sorry but you do a google search for pick up sensor 34.0 error and see if you can find the sensor... this is just here to save someone the time it took me.

All of that info is from the Workshop manual.
And you will have to remove the side cover if you are REPLACING the sensor with a new one.
To measure the correct air gap from timeing gear to tip of NEW sensor

You can measure the gap even with a new sensor without pulling the cover.
Ciao

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

ducati 1098 pick up sensor

ducati 1098 pick up sensor error

ducati monster error pkup

ducati monster pickup sensor

ducati monster pk.up

ducati pick up sensor

ducati pickup sensor

ducati pkup error

error pick .up 34.0

pick up sensor ducati

February 15th, 2011, 09:45 AM	#1
Mr Jurassic Senior Member ducatis in the registry: [1198] [view ducati.org album] Join Date: Mar 2009 Location: Victoria,TX Posts: 688	PK.UP Sensor Error 34.0 Fix Ok guys i recently had this error and people have been looking for this pick up sensor well after 5 hours of research i finally found it. In picture #1 you can see this is the left side of the bike. This is the Timing pick-up sensor here In picture #2 this is is the hole where it goes. double check the quality of these o rings In picture #3 After cleaning the sensor re-grease only the tip of the sensor In picture #4 Fitment of the sensor back into the crackcase In picture #5 position the 0.6mm shim NOTE: if replaceing the sensor you will have to take the side of the crankcase off and measure the air gap between the sensor and the teeth on the timing gear. The distence between the timing gear and the sensor should be between .8 and .6 mm NOTE: I am not responsible for voiding/ or blowing up of any engines. Attached Images __________________ BIKES OWNED 2008 EJ-250R RED------------------Kawasaki (Sold) 2008 cbr1000 light blue/black-----Honda (Wifes) TOTALED 02/20/2010 2006 ZX-6R (636) White-----------Kawasaki 2009 1198 White---------------------Ducati

February 15th, 2011, 10:08 AM	#2
lucky phil Senior Member No ducatis in the registry Join Date: Feb 2009 Posts: 789	It took you 5hrs to find the pickup sensor?OK You dont need to lube the end of the sensor,first oring will simply wipe it off and there will be nothing on it when it hits the second ring.Better to smear grease down the hole to help it ease through the o rings. You dont need to remove the side cover to set the gap.There are a couple of ways to do it without resorting to that depending on the equipment you have available. Ciao

February 15th, 2011, 10:17 AM	#3
Mr Jurassic Senior Member ducatis in the registry: [1198] [view ducati.org album] Join Date: Mar 2009 Location: Victoria,TX Posts: 688	I agree.... Just those are pic's and instructions from the workshop manual... sorry but you do a google search for pick up sensor 34.0 error and see if you can find the sensor... this is just here to save someone the time it took me. All of that info is from the Workshop manual. And you will have to remove the side cover if you are REPLACING the sensor with a new one. To measure the correct air gap from timeing gear to tip of NEW sensor __________________ BIKES OWNED 2008 EJ-250R RED------------------Kawasaki (Sold) 2008 cbr1000 light blue/black-----Honda (Wifes) TOTALED 02/20/2010 2006 ZX-6R (636) White-----------Kawasaki 2009 1198 White---------------------Ducati Last edited by Mr Jurassic; February 15th, 2011 at 10:26 AM.